Ultimate Installation Of 6 0 Powerstroke Bulletproof Diesel Oil Coo The factory oil cooler in your 6.0l powerstroke can cause overheating and put your engine at risk. in this video, mike will walk us through the steps needed. Some engines, like the 6.0 power stroke, take this a step further by adding a cooler to extract heat directly from the oil. while the 6.0’s oil cooler is effective, it also has a history of pattern failures. these problems can be addressed by installing a 6.0 oil cooler relocation kit or a complete 6.0 power stroke oil cooler upgrade. common.
Oil Cooler Flush Ford 6 0l Powerstroke Xdp Blog View attachment 6.0l intake manifold.pdf. :usa: 2005 f350 cclb 4x4. arp studs. bpd egr cooler, remote oil cooler, 58v ficm, water pump, 7.3 fan mod, bypass oil filter. owdawg intake. mishimoto intercooler pipes and boots. mishimoto radiator intercooler. mishimoto 202* thermostat. Received 57 likes on 46 posts. after reading this thread thought i would order a couple of the usa made seal kits for oiler cooler. ford parts direct, autonation, and amazon say the kit does not fit my 2004 6.0. tasca changes the part number to 3c3z 9n693 aa and shows it as a single o ring for $5.07. Insert the 5 16” x 1 1 4” bolt (the longer of the three 5 16” bolts provided) with a 5 16” flat washer through the oil filter mounting bracket and the hole at high point (top of the triangle) on the oil filter adapter. use a 5 16” flat washer and nut on the oil filter adapter side to secure the bolt. By opting for a factory style replacement oil cooler, the part can range from about $200 to $500 depending on where you buy it, or even more importantly the quality of the part. for a factory style replacement this is probably one of the best options: new motorcraft oil cooler 6.0l $439.83 because the factory oil cooler was prone to repetitive.
How To Install Deisel Oil Cooler Housing On 6 0 Ford Powerstroke Insert the 5 16” x 1 1 4” bolt (the longer of the three 5 16” bolts provided) with a 5 16” flat washer through the oil filter mounting bracket and the hole at high point (top of the triangle) on the oil filter adapter. use a 5 16” flat washer and nut on the oil filter adapter side to secure the bolt. By opting for a factory style replacement oil cooler, the part can range from about $200 to $500 depending on where you buy it, or even more importantly the quality of the part. for a factory style replacement this is probably one of the best options: new motorcraft oil cooler 6.0l $439.83 because the factory oil cooler was prone to repetitive. 6.0l power stroke diesel 6.0 oil cooler leak. advice input needed. i have a 2004 6.0 with 170,000 miles on it. i noticed that i had some oil leaking on my driveway. upon further inspection i found that the oil was coming from the top and rolling down the bell housing. put dye inside the oil, ran it for a week and. This is a direct replacement for the factory oil cooler found on the 6.0l powerstroke engines, both truck and van. this is the new and improved design from ford and is a more effective cooler than the original, failure prone model. kit comes complete with gaskets and replacement screen. ford p n:3c3z 6a810 a.
6 0 Liter Powerstroke Oil Cooler Intake Install Youtube 6.0l power stroke diesel 6.0 oil cooler leak. advice input needed. i have a 2004 6.0 with 170,000 miles on it. i noticed that i had some oil leaking on my driveway. upon further inspection i found that the oil was coming from the top and rolling down the bell housing. put dye inside the oil, ran it for a week and. This is a direct replacement for the factory oil cooler found on the 6.0l powerstroke engines, both truck and van. this is the new and improved design from ford and is a more effective cooler than the original, failure prone model. kit comes complete with gaskets and replacement screen. ford p n:3c3z 6a810 a.
Comments are closed.